0 0
Hello Guest Login    |    Registration
HG Hydraulic wiper rings

HG Hydraulic wiper rings

  $0.00
Description


Description:

The wool ring WSL has an edge of high mobility on the dynamic side, and on the static - a sturdy, shorter, outstanding edge. This special profile protects the rod and the static side (at the landing site) from contamination, debris and water. Strong dirt can damage the seal and cause corrosion of the inside of the cylinder.


Technical specifications:

Speed: < 1 m/s.

Temperature: from -35В°C to +100В°C with a peak value of +110В°C

Operating environment: water at room temperature, mineral oils (see Table 1 on page 1.2.4).


Material:

Name: polyurethane (PU) with high modulus of elasticity, low permanent deformation and high abrasion resistance.

Hardness: Shore 93 Рђ 2.

Material code: C0.


Installation:

Installation does not cause any complications, as it is carried out in a semi-open groove in the nearest part outside the cylinder.

The allowable surface roughness should be maintained to avoid ring scratching during installation.

(For more information, see the Installation Instructions on page 1.2.14).


pcs.
  $0.00
Description


Description:

The function of the wiper ring WSG is to clean the rod during the return to its original position and to protect it from external contamination. This type of structure includes a metal frame connected to a polyurethane element.


Technical specifications:

Speed: < 0,8 m/s.

Temperature: from -35В°C to +100В°C with a peak value of +110В°C.

Operating environment: atmospheric factors, water at a temperature below +60В°C, mineral oil (see Table 1 on page 1.2.4).


Material:

As a material for a wool ring, polyurethane is used with a hardness of 93 Shore A and a steel frame.

Material code: CA.


Installation:

Installation is carried out in an open landing groove.

Observe the permissible surface roughness for a more convenient installation of the wiper ring.

Caution: The size of the landing groove of the wiper ring should be within tolerance, as shown in column D. If the above values are not observed, the seal may be squeezed out during operation.


pcs.
  $0.00
Description


Description:

The function of the wiper ring R09 is to clean the rod during return to its original position and to protect it from external contamination.

This type of structure includes a metal frame connected to a polyurethane element.

The structure of this type includes a straight metal frame connected to an element of NBR material.


Technical specifications:

Speed: < 1 m/s.

Temperature: -30В°C to +100В°C.

Operating environment: atmospheric factors, water, sand, etc. (see Table 1 on page 1.2.4).


Material:

The material used in the manufacture of the wiper ring is nitrile rubber NBR 90 Shore A, steel part - AISI 1010.

Material code: NG.


Installation:

Installation is carried out in an open landing groove.

For a more convenient installation of the seal, the allowable surface roughness.

Caution: The size of the landing groove of the wiper ring should be within tolerance, as shown in column D. If the above values are not observed, the seal may be squeezed out during operation.


pcs.
  $0.00
Description


Description:

The WWS wraparound ring, unlike other profiles, has a protrusion on the static part that fixes it to the landing groove. This fact provides an automated assembly and greatly facilitates the mechanical design of the groove.

There are grooves on the inner base of the mud ring, creating a stabilizing and providing venting effects, which helps to avoid problems with extrusion


Technical specifications:

Speed: < 1 m/s.

Temperature: from -35В°C to +100В°C with a peak value of +110В°C.

Operating environment: water at room temperature, mineral oils (see Table 1 on page 1.2.4).


Material:

The material used is flexible polyurethane (even at low temperatures), with high abrasion resistance.

Standard polyurethane 90 Shore A (B0) in diameter up to 35 mm.

For larger sizes, the standard polyurethane 93 Shore A (C0).

Material code with a diameter of 35 mm: B0.

Material code with diameter> 36mm: C0.


Installation:

Installation is more convenient, since it is carried out in a semi-open groove.

It is necessary to ensure an acceptable value of the roughness of the surface of the landing groove.

(For more details, see the Installation Instructions on page 1.2.14).


pcs.
  $0.00
Description


Description:

Thanks to its special profile and design, the WAT wiper ring can be self-aligned when the stem is displaced during operation. The cuff has two edges: an edge closer to the stem, longer, very flexible and movable; The edge of the static part is shorter and prevents contamination from coming into contact with the locking protrusion.


Technical specifications:

Speed: < 1 m/s.

Temperature: from -35В°C to +100В°C with a peak value of +110В°C.

Operating environment: water at room temperature, mineral oils (see Table 1 on page 1.2.4).


Material:

Material: polyurethane type ""C0"", with high modulus of elasticity, low permanent deformation and high abrasion resistance.

Standard polyurethane 90 Shore A (B0) in diameter up to 35 mm.

Hardness: Shore 93 A 2.

It is also possible to use more rigid types of polyurethane for a highly contaminated working environment.

Material code: C0.


Installation:

Installation is more convenient, since it is carried out in a semi-open groove.

It is recommended that the permissible surface roughness is observed (grind the surface of the landing groove).

(For more details, see the Installation Instructions on page 1.2.14).


pcs.
  $0.00
Description
Transmission chains roller conveyor long-unit (TRD)

Chain name P d1 max b1 min d2 max Lc max h2 max a1 D b6 max C max Ultimate
load
mm mm mm mm mm mm mm mm mm mm kN
TRD-38-3000-1-1-6-Рў 38,00 15,88 22,00 7,92 42,00 21,30 30,00 6,60 23,00 80,00 30,00
TRD-38-4000-1-1-6-Рў 47,00 26,00 40,00
TRD-38-3000-1-1-8-Рў 42,00 8,40 23,00 30,00
TRD-38-4000-1-1-8-Рў 47,00 26,00 40,00
TRD-31,75-2300-1-1-6-Рў 31,75 10,16 9,65 5,08 24,00 14,80 26,00 6,60 13,00 72,00 23,00
TRD-38-3000-1-2-6-Рў 38,00 15,88 22,00 7,92 42,00 21,30 26,00 6,60 23,00 72,00 30,00
TRD-38-4000-1-2-6-Рў 47,00 26,00 40,00
TRD-38-3000-1-2-8-Рў 42,00 8,40 23,00 30,00
TRD-38-4000-1-2-8-Рў 47,00 26,00 40,00
TRD-38-4400-1-2-8-Рў 16,50 47,00 90,00 44,00
TRD-31,75-2300-1-2-6-Рў 31,75 10,16 9,65 5,08 24,00 14,80 6,60 13,00 72,00 23,00
TRD-38-3000-2-1-6-Рў 38,00 15,88 22,00 7,92 42,00 21,30 30,00 6,60 23,00 72,00 30,00
TRD-38-4000-2-1-8-Рў 47,00 8,40 26,00 40,00
TRD-31,75-2300-2-1-6-Рў 31,75 10,16 9,65 5,08 24,00 14,80 26,00 6,60 13,00 23,00
TRD-38-3000-2-2-6-Рў 38,00 15,88 22,00 7,92 42,00 21,30 26,00 6,60 23,00 80,00 30,00
TRD-38-4000-2-2-6-Рў 47,00 26,00 40,00
TRD-38-4000-2-2-8-Рў 8,40
TRD-38-4400-2-2-8-Рў 16,50 6,60 86,00 44,00
TRD-31,75-2300-2-2-6-Рў 31,75 10,16 9,65 5,08 24,00 14,80 13,00 72,00 23,00
TRD-38-3000-3-6-Рў 38,00 15,88 22,00 7,92 42,00 21,30 30,00 6,60 23,00 80,00 30,00
TRD-38-3000-3-10-Рў 33,00 10,50
TRD-38-4000-3-10-Рў 47,00 26,00 40,00
TRD-31,75-2300-3-1-6-Рў 31,75 10,16 9,65 5,08 24,00 14,80 26,00 6,60 13,00 72,00 23,00
TRD-38-3000-4-1-6-Рў 38,00 15,88 22,00 7,92 42,00 21,30 40,00 6,60 23,00 72,00 30,00
Name
Roller conveyor long-unit (TRD)
pcs.
  $0.00
Description


Description:

The WED ring scraper is a combined profile where the seal is equipped with a wiping edge on the outside and a sealing lip inside.

Dimensions are interchangeable when installing the wiper in standard grooves.

Scraped edge is very flexible, can even out the deviation of the rod. The sealing portion has a harder and longer edge for providing a sealing action and maintaining the lubricating layer on the stem.


Technical specifications:

Pressure: < 20 bar.

Speed: < 1 m/s.

Temperature: from -35В°C to +100В°C with a peak value of +110В°C.

Operating environment: water at room temperature, mineral oils (see Table 1 on page 1.2.4).


Material:

Name: polyurethane type ""C0"" with high modulus of elasticity, low permanent deformation and high abrasion resistance.

Hardness: Shore 93 A 2. It is also possible to use more rigid types of polyurethane for more polluted working conditions.

Material code: C0.


Installation:

The installation becomes much easier, since it can be produced in a semi-open groove.

It is recommended that the permissible surface roughness of the landing groove.

(For more information, see the Installation Instructions on page 1.2.14).


pcs.
  $0.00
Description


Description:

The WEL scuff is typically used in one-way cylinders that are open on one side.

Due to its cleaning function, the inverted seal profile prevents the inner wall of the cylinder from deteriorating, which can be caused by atmospheric phenomena, condensation and other environmental factors.


Technical specifications:

Pressure: 0.

Speed: < 1 m/s.

Temperature: from -35В°C to +100В°C with a peak value of +110В°C.

Operating environment: water, dust or other atmospheric phenomena (see Table 1 on page 1.2.4).


Material:

Name: polyurethane type ""C0"" with high modulus of elasticity, low permanent deformation and high abrasion resistance.

Hardness: Shore 93 A.

Material code: C0.


Installation:

The installation is carried out by applying a half-open groove with a chamfer to prevent extrusion of the mud ring during the reverse cycle.

It is recommended that the permissible surface roughness of the landing groove.


pcs.
  $0.00
Description


Description:

Type BWA combines a profile with an asymmetrical edge and a wiper ring.

Since the seal is mounted in a separate mounting groove, the BWA cuff has the following advantages:

reduced sizes;

faster design of the seat.


Technical specifications:

Pressure: < 20 bar.

Speed: < 1 m/s.

Temperature: -30В°C to +90В°C.

Operating environment: air with or without lubricant, mineral oil or grease (see Table 1 on page 1.2.4).


Material:

Standard material: polyurethane 90 Shore A.

Standard material code: B0.

Alternative material: 85 Shore A.

Alternative material code: A0.


Installation:

It is necessary to observe a certain value of the roughness of the surface of the seat where the wiper ring is installed, in order to minimize wear of the seal during operation.


pcs.
  $0.00
Description


Description:

Type BWS combines a seal with an asymmetric edge and a wiper ring. Sealing edge type BWS has a rounding guaranteeing the greatest smoothness, and a small The protrusion on the static part simplifies installation (especially for small diameters).

The scraping part is a very thin edge, which does not affect the sticking effect when the cylinder moves.


Technical specifications:

Pressure: < 20 bar.

Speed: < 1 m/s.

Temperature: -30В°C to + 90В°C.

Operating environment: air with or without lubricant, mineral oil or fat (see Table 1 on page 1.2.4).


Material:

Standard material: polyurethane 90 Shore A.

Standard material code: B0.

Alternative material: 85 Shore A.

Alternative material code: A0.


Installation:

It is recommended to thoroughly polish the seat where the wiper ring will be installed, to minimize wear of the seal during operation.

Caution: for use in extreme conditions with inconsistency or instability, for diameters greater than 16 mm, it is recommended to fix the base of the wiper ring to the landing groove, and not just to the ledge.


pcs.